Neutrino-Pub

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Team B ======
**Instructor**: Dr. Son Cao

**Supporter**: Ph.D. student Quyen Phan; M.Sc. Sang Truong

**Members**:
  * Nguyen Thi Yen Binh
  * Trinh Hoang Dieu Ngan
  * Dang Quoc Trieu
  * Nguyen Duc Phu
  * Nguyen Thi Nhung

[[https://ifirse.icise.vn/nugroup/hardwarecamp/uploads/Hardware_Camp_Beamer-GroupB.pdf|Group B Final presentation]] and [[https://ifirse.icise.vn/nugroup/hardwarecamp/uploads/GroupB%20-%20Hardware%20Camp%20Report.pdf|final report]]
===== Targets =====
  * **MPPC properties**
    * observe 1pe, 2pe and the corresponding threshold 
    * check the rising/falling time (note the definition of the rising and falling time)
    * dark count rate with 1pe; 2pe; 3pe
    * check `pattern` trigger (need calibration?) with coincidence of 2, 3
      * Use DRS4 waveform generator (or Arduino) for example 
      * Coincidence gate 

  * **Fluorescence lifetime by exciting with UV LED** 
    * Measure rising/falling time with oscilloscope (note the signal size)
    * Fit with exponential and/or oscilloscope measurement function 

  * **Cosmic muon counter** 
    * calculate the rate with area of detector (size of plastic scintillator)
    * Scintillator inefficiency (rate of 1,2,4; vs rate of 1,2,3,4)
    * Muon Signal corresponding to how many P.E?

===== Hands-on Activities =====
1. Act#1 (1.5h, Feb. 27 AM): safety, lab arrangement, components, rules; light source (LED)  driven with waveform generator, arduino or analog discovery; various LED wavelength; soldering a circuit for LED (this is to use with MPPC later, so think a bit about design to easily coupling to MPPC (direct or with optical fibers, mimicking the use of the WLS))

2. Act #2 (1.75h, Feb. 27 PM) oscilloscope functionality, signal generation with analog discovery, counting function  and coincidence pattern trigger

3. Act #3 (2.75h, Feb. 28 AM): Single MPPC circuit; soldering, testing signal, pedestal; noise mitigation with Faraday case, checked if can see single P.E without amplifier? 

4.  Act #4 (2.75h, Feb. 28 PM): Start working with MPPC array; measure MPPC characteristics (noise rate, gain; timing response); measure the fluorescence lifetime with Thorlabs fluorescence plates

5.  Act #5 (2.75h, Mar. 1 AM): Continue with fluorescence lifetime measurement if needed. measure coincidence rate. Work in combination of Scintillator, wavelength shifting fiber and photosensor; concept of muon counter; NIM modules to use: discriminator, scaler, coincidence (and delay if needed)

6.  Act #6 (2.75h, Mar. 1 PM): Data taking and analysis

7.  Act #7 (2.75h, Mar. 2 PM): Data taking and analysis 

8. Act #8 (2.75h, Mar. 3 AM): Data taking and analysis

9.  Act #9 (2.75h, Mar. 3 PM): Data taking and analysis 

===== Hardware availability =====
  * MPPC array 4 x4, model Hamamatsu S13361-3050AE-04, specification [[https://www.hamamatsu.com/content/dam/hamamatsu-photonics/sites/documents/99_SALES_LIBRARY/ssd/s13361-3050_series_kapd1054e.pdf]]
    * AiT power supply [[model ABPS]] and amplifier [[model PBA116L]]
  * One single MPPC S13360-1225 [[https://www.hamamatsu.com/content/dam/hamamatsu-photonics/sites/documents/99_SALES_LIBRARY/ssd/s13360_series_kapd1052e.pdf]]: try to soldering; check and suppress the noise. No need amplifier to observe the signal; use along with Matsusada low-noise DC power supply 
  * 4 plastic scintillator  and wavelength shifting fiber 
    * size: **2.5cm width x 1.3 cm thick x 25 cm long**
  * Oscilloscope SDS 1104X-E/ with ethernet connected [[https://siglentna.com/USA_website_2014/Documents/UserManual/SDS1000X&Xplus_UserManual_UM0101X-E02A.pdf]]
  * Optical fibers (Thorlabs 2m) and unknown 
  * DAQ PC: IFIRSE06/ Ubuntu 22.04; relevant software available: ROOT, GEANT4